AC repair
Furnace & heating
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateTrusted Furnace Replacement for San Mateo Homeowners
When a furnace starts short-cycling, blowing lukewarm air, or costing more each month to run, replacement often makes more sense than another repair. We replace residential furnaces across San Mateo, and we do it with a written fixed price, a scheduled install date, and no pressure to buy equipment you don’t need. Our technicians have up to 9 years of experience, and every one of them works on heating and cooling only, so the assessment you get is from a specialist rather than a generalist. We install equipment from Rheem, York, Bryant, and other major brands, matched to your home and budget instead of a dealership quota. Call (866) 260-3183 for a free estimate. We answer 24/7.

Key Takeaways
- Furnace replacement in San Mateo is a scheduled job, not a same-day fix: it’s sized, ordered, and installed on a set date.
- We work across major brands, so the recommendation fits your home and budget.
- Every replacement comes with a written fixed price before any work begins.
- We handle both heating and AC Repair San Mateo work, so one call covers the whole system.
What Our Furnace Replacement Service Includes
Replacing a furnace is more than sliding a new box into the old spot. The work covers sizing, removal, installation, and the checks that make sure the system runs safely and efficiently in a San Mateo home. Here’s what’s involved.
Load Calculation and System Sizing
Before we quote a replacement, we measure the home and calculate the heating load so the new furnace matches the space it’s heating. An oversized furnace short-cycles, wastes fuel, and wears out faster; an undersized one never keeps up on a cold morning. This step is why we don’t quote a replacement over the phone from a model number alone.
Removal and Safe Disconnection
We disconnect the old unit, including the gas line and electrical connections, and remove it without disturbing the surrounding ductwork or the platform it sits on. Gas and electrical work on a furnace is not a homeowner job; it takes a trained technician to shut it down safely. We also check the venting and flue path while the old unit is out, since a replacement is the right time to catch a venting problem.
New Furnace Installation
We set the new furnace, reconnect gas and electrical, seal the connections, and confirm the unit fires and runs through a full cycle. Installation includes checking airflow and static pressure so the equipment isn’t fighting a restricted duct system. If the ducts need attention, we’ll tell you before the install date, not after.
Combustion and Safety Testing
After install, we test combustion and confirm the furnace is venting properly and running within spec. This is the step that protects your household, and it’s one we never skip. You get the results and a clear explanation of what they mean.
Thermostat and Controls Check
We confirm the thermostat is compatible with the new equipment and set up correctly for the home. If your existing thermostat is aging or doesn’t match the new furnace’s capabilities, we’ll discuss options as part of the estimate. A mismatched control is a common reason a new furnace underperforms.
Styles & brands we work with
- AC repair
- Furnace & heating
- Heat pumps
- Ductless mini splits
- Carrier
- Trane
- Goodman
Brands We Service for Furnace Replacement
We install and service equipment from nine major brands: Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. That range matters because we’re not tied to a single manufacturer’s lineup. We look at what’s in your home now, what your ducts and layout can handle, and what fits your budget, then recommend from there. If a Rheem unit is the sensible fit for your space, that’s what we’ll suggest. If a Bryant or York model makes more sense, we’ll say so.
We know these systems well enough to recognize where each one tends to wear and what to check first when something’s off. Whether you have a Rheem, a York, a Daikin, a Bryant, or any other make, we can help you sort out whether repair or replacement is the right call.
Signs You Need Furnace Replacement Right Now
- Repeated repairs in a short span. If you’ve paid for multiple fixes in the last couple of seasons, the money is going into a system that’s telling you it’s done. At some point replacement costs less than keeping an old unit limping along.
- Rising energy bills without a change in use. A furnace that’s losing efficiency quietly burns more gas to deliver the same heat. If your bills climb while your habits haven’t changed, the equipment is a likely culprit.
- Uneven heat or rooms that never warm up. Cold rooms and hot rooms can point to a furnace that can’t keep up or a system that’s never been sized right for the home. A load calculation tells you which.
- Strange smells, sounds, or a yellow flame. A persistent metallic or burning smell, banging or rumbling on startup, or a flame that isn’t blue can signal a safety concern. Shut the system down and call a technician rather than diagnosing it yourself.
- Age and parts availability. Older furnaces eventually reach a point where parts are hard to find and repairs stall. When a system is that far along, replacement is usually the smarter path.
Our Furnace Replacement Process – Step by Step
- 1
Assessment and load calculation. We inspect the existing furnace, measure the home, and run a heating load calculation. This gives us the right size and shows whether ductwork or venting needs attention.
- 2
Written fixed-price estimate. We put the recommendation and the price in writing, itemized so you can see what’s included. No surprises after the work starts.
- 3
Scheduling and equipment order. Replacement is a scheduled job: we order the equipment and set an install date with you. This isn’t same-day work, and it shouldn’t be.
- 4
Installation day. We disconnect and remove the old unit, set the new furnace, reconnect gas and electrical, and seal everything properly. We test combustion and airflow before we call it done.
- 5
Final walkthrough. We walk you through the new system, confirm the thermostat is set up, and leave you with the paperwork. If anything needs a follow-up, we schedule it.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Furnace Replacement Cost in San Mateo?
Furnace replacement in San Mateo typically runs $4,130 – $8,850 depending on the size of the system, the efficiency level you choose, and whether ductwork or venting needs work alongside the install. A straightforward like-for-like replacement in a smaller home lands toward the lower end. A larger home, a higher-efficiency unit, or a job that includes duct corrections or venting repairs moves toward the upper end. If you’re comparing repair against replacement, a furnace repair typically runs $175 – $825, which is useful context when weighing the two.

Several things affect the price: the heating capacity the home actually needs, the efficiency rating of the equipment, whether the existing venting is compatible, and whether the install requires any duct modification. Choosing a unit that’s oversized or packed with features you won’t use is a common way to overpay. Our approach is to size the system to the home and recommend equipment from your budget range, not push a premium unit. The free estimate includes the load calculation, the equipment recommendation, and an itemized price, and the written estimate sets the final price.
Furnace Replacement Near San Mateo – Our Service Area
We connect homeowners with independent local HVAC professionals across the Peninsula and South Bay, including San Mateo, Hayward, and Sunnyvale, as well as Fremont, Santa Clara, Saratoga, Burbank, Campbell, Monte Sereno, and Los Gatos. Replacement work is scheduled, so timing depends on equipment availability and your calendar rather than distance. Call (866) 260-3183 to check scheduling for your area. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Serving San Mateo, CA – Our Local Coverage Area
We serve San Mateo and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Furnace Replacement in San Mateo
Furnace replacement is removing an old heating unit and installing a new one sized to your home. It includes disconnecting the old unit, setting and connecting the new furnace, testing combustion and airflow, and confirming the thermostat works with the new equipment. It’s different from a repair, which fixes a specific component on the existing system. If you’re unsure which you need, we’ll assess it and tell you straight.
Most residential replacements take about a day once the equipment is on site. The actual timeline depends on the home, whether ductwork or venting needs work, and how accessible the furnace location is. Because the job is sized and scheduled in advance, you’ll know the expected install date before we start. Call (866) 260-3183 to get scheduling for your home.
A typical furnace replacement in San Mateo runs $4,130 – $8,850, depending on system size, efficiency level, and any duct or venting work. Higher-efficiency equipment and larger homes move toward the upper end. We give a written fixed-price estimate before any work begins, and the written estimate sets the final price. Call (866) 260-3183 for a free estimate.
Yes. We install and service Rheem, York, Daikin, Bryant, Carrier, Trane, Lennox, Goodman, and American Standard equipment. We’re not tied to a single manufacturer, so the recommendation fits your home and budget. Whether you have Rheem, York, or any other major make, we can help.
No. Furnace replacement is a scheduled job because the equipment is sized and ordered for your home first. Same-day work fits repair calls, not a full system swap. We answer 24/7 and set install dates Sunday through Friday, 7am to 7pm. If your furnace has failed, call (866) 260-3183 and we’ll discuss repair options and scheduling.
Warranty coverage depends on the equipment manufacturer and the specific unit you choose, so we confirm the terms in writing as part of your estimate. You’ll see the coverage before the install date, not after. Ask us to walk through the warranty on any unit you’re considering.
Clear access to the furnace, including the path to it and the space around it, and move anything fragile away from the work area. If your furnace is in a closet or crawl space, make sure we can get to it easily. Beyond that, we handle the rest, and we’ll tell you in advance if anything specific is needed.
Schedule Your Furnace Replacement Service in San Mateo Today
If your furnace is on its last leg, a replacement sized to your home and priced in writing is the honest next step. Call (866) 260-3183 for a free, no-obligation estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. We’ll assess your system, size the replacement correctly, and set an install date that works for you.
Written by the team at AC Repair San Mateo.